Solved question paper for SSDR May-2017 (DIPLOMA 6th)

Home
psbte
diploma
civil
6th
ssdr
May-2017

Solved Question Paper

Steel structures design and drawing May-2017

PSBTE • DIPLOMA • Cvil Engineering • 6th • May-2017

SSDR for Punjab State Board of Technical Education in Diploma in Engineering, Civil Engineering, 6th Semester helps students find subject-wise previous year question papers and old papers for exam preparation. This page is useful for revision, understanding the exam pattern, and seeing how questions are framed in Steel Structures Design and Drawing. It is intended to support year-wise and semester-wise paper search for students looking for practice before exams. BRpaper is not the official website of the university or board, and the papers here should be used as study support for preparation and revision.

Question papers (year-wise) Solutions

Solved Questions

Solved

The edge distance in riveting should be greater than

Fill in the Blanks 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
A line of rivets parallel to the direction of stress is called as

Fill in the Blanks 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Dec 2016 The line of the rivets parallel to the direction of stress is called _________.
Brittleness is often referred to as

Fill in the Blanks 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
A built up beam to carry heavier loads over large span is called a

Fill in the Blanks 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Dec 2015 A built up beam to carry heavier loads over large span is called a

The effective length of column depends upon

Fill in the Blanks 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
ISSQ 50 rolled section means

Fill in the Blanks 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Struts are the members of roof trusses.

Fill in the Blanks 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Roof beam supported by roof trusses is called as.

Fill in the Blanks 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.

Lap, tee, or corner joints require type welds.

Fill in the Blanks 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
May 2018 Lap, Tee or corner joints required ____________ weld.

May 2008 Lap, tee or corner joints require ______ weld.
Strength of beam depends upon

Fill in the Blanks 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
May 2018 The strength of beam depends upon ____________.
Side fillet welds are also called longitudinal fillet weld.

True / False 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Plasticity is the extreme opposite to elasticity.

True / False 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.

For mild steel, yield stress fy =350N/mm2

True / False 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
When one end is fixed, other hinged then effective length=0.65L

True / False 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Bending stress at neutral axis is zero.

True / False 1 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Explain the advantages and disadvantages of welding.

Short Answer 5 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
May 2022 Write disadvantages of welded joints.

May 2019 What are disadvantages of welding?

May 2018 Explain the advantages and disadvantages of welded joint.

Explain the strength of riveted joint.

Short Answer 5 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Dec 2016 What is shearing strength of a riveted joint?
What are tacking rivets? Explain their purposes in steel structures.

Short Answer 5 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Explain the purposes of structural steel used in engineering structures.

Short Answer 5 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
May 2022 What is fabrication of steel structures?

May 2018 What do you mean by structural steel? Explain its properties.

Dec 2018 Important considerations in fabrication and erecting of steel structures.

May 2017 Explain the important considerations in fabrication and erection of steel structures.
Explain the function of column bases in steel structures.

Short Answer 5 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
May 2010 Explain what do you understand by a gusseted base for a steel column.

Explain various types of Angle Struts used in trusses.

Short Answer 5 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Dec 2015 Explain various forms of trusses with sketches.
Explain the detail of fixing purlin with principal rafter with sketches.

Short Answer 5 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Explain the assumptions made in the theory of simple bending

Short Answer 5 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
May 2018 What are the assumptions made with theory of simple bending?

May 2015 Write the assumptions in the theory of simple bending in case of flexural members.
Explain the important considerations in fabrication and erection of steel structures.

Short Answer 5 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
May 2022 What is fabrication of steel structures?

May 2018 What do you mean by structural steel? Explain its properties.

Dec 2018 Important considerations in fabrication and erecting of steel structures.

May 2017 Explain the purposes of structural steel used in engineering structures.

Find the suitable pitch for triple riveted lap joint for plates 12mm thick. Use PDSR rivets. Take permissible tensile stress in plate = 150MPa. Determine the efficiency of the joint also.

Long Answer 10 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Dec 2018 Two plates 12 mm and 10 mm thick are joined by a triple riveted lap joint. Find the suitable pitch for the outer row of rivets if the pitch for central row of rivets is half of the pitch for outer rows. Take allowable tensile stress = 150 N/mm2. Use Power Driven Shop Rivets. Also find the efficiency of the joint.

May 2015 Two plates 12mm and 10 mm thick are joined by a triple riveted lap joint. Find the suitable pitch for the outer row of rivets if the pitch for central row of rivets is half of the pitch for outer rows. Take allowable (safe) tensile stress =150 N/mm2. Use Power Driven Shop Rivets. Also find the efficiency of the joint.

Dec 2008 Two plates 12 mm and 10 mm thick are joined by a triple riveted lap joint. Find the suitable diameters, central and outer rows of rivets. In half the pitch for outer rows. Take allowable tensile stress in plate = 150 N/mm². Use power driven shop rivets. Also find the efficiency of the joint.
Two channels ISLC300@324.7N/m with flanges butting and welded toe to toe are to be used as a column. The length of the column is 4 m and is restrained in position but not in direction at both ends. Take fy =250N/mm2 Calculate the safe load that can carry the column.

Long Answer 10 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Design an unequal angle as a tie member 2m long, in a bridge to carry an axial load of 150kN.Using power driven rivets at joints. Allowable tensile stress = 150 N/mm2

Long Answer 10 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Calculate the safe load carrying capacity of a discontinuous double angle strut made up of 2 -ISA100X75X6 mm. placed back to back on the same side of a gusset plate 8mm thick by one rivet at ends. Center to center length of strut is 2.15m.

Long Answer 10 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.
Dec 2017 A discontinuous strut having effective length 2m consist of two equal angles ISA 50x50x6 mm it is connected to the opposite sides of gusset plates by two rivets on each angle at two ends. Calculate the load carrying capacity of the strut.

May 2016 A discontinues angles strut consist of two ISA 90 x 60 x 8 placed back to back and connected on both sides of 10 mm thick gusset plate by using a fillet weld. Calculate its load carrying capacity.

Design a suitable section of steel beam having an effective span of 8m and which carries the superimposed load of 40kN/m Take E = 2x105N/mm2 Apply the checks for shear and deflection.

Long Answer 10 Marks May-2017 • PSBTE DIPLOMA

Existing answers are stored as HTML; you can edit directly without converting to Markdown.

Explore all data

FAQ

Frequently Asked Questions

Answers about this subject, solved papers, and preparation.

Updated regularly

01 Where can I find SSDR previous year question papers?

This page is meant to help students खोज subject-wise SSDR previous year question papers for PSBTE Diploma Civil Engineering 6th semester.

02 Is SSDR the same as Steel Structures Design and Drawing?

Yes, SSDR refers to Steel Structures Design and Drawing for Civil Engineering 6th semester.

03 Can I use old SSDR papers for revision?

Yes, old SSDR papers are useful for revision, practice, and understanding the question pattern used in exams.

04 Are these official PSBTE question papers?

No. BRpaper is not the official website of Punjab State Board of Technical Education. It only helps students find study material and previous year papers.

05 Do you provide solved SSDR papers?

This page is focused on previous year and old question papers. Solved papers may not be available for every year.

Solved question paper for SSDR May-2017 (DIPLOMA 6th)

Steel structures design and drawing May-2017

Solved Questions

Explore all data

PTU

PU Chandigarh

PSBTE

PSEB(School)

BFUHS

PU-PATIALA

GNDU

HPTSB

GTU

MDU

MRSPTU

CBSE(School)

BSEH

UBSE

PTU DISTANCE EDUCATION

Frequently Asked Questions